-
1 root-mean-square voltage
Metrology: rms voltageУниверсальный русско-английский словарь > root-mean-square voltage
-
2 действующее напряжение
Русско-английский научно-технический словарь Масловского > действующее напряжение
-
3 действующее напряжение
Русско-английский словарь по электроэнергетике > действующее напряжение
-
4 действующее значение напряжения
действующее значение напряжения
—
[Интент]Недопустимые, нерекомендуемые
Тематики
- электротехника, основные понятия
EN
Русско-английский словарь нормативно-технической терминологии > действующее значение напряжения
-
5 действующее напряжение
1) General subject: actual stress2) Aviation: active tension3) Engineering: effective voltage, net voltage, rms voltage, root-mean-square voltage4) Construction: working stress5) Telecommunications: active voltage6) Oil: effective stressУниверсальный русско-английский словарь > действующее напряжение
-
6 эффективное напряжение
1) Geology: actual stress2) Engineering: effective stress, effective voltage, net voltage, root-mean-square voltage3) Construction: intergranular stress4) Electronics: rms voltageУниверсальный русско-английский словарь > эффективное напряжение
-
7 среднеквадратическое значение напряжения
Engineering: mean square voltage, rms voltage, root-mean-square voltageУниверсальный русско-английский словарь > среднеквадратическое значение напряжения
-
8 среднеквадратичное напряжение
Engineering: rms voltage, root-mean-square voltageУниверсальный русско-английский словарь > среднеквадратичное напряжение
-
9 действующее напряжение
эл. rms voltage, effective voltage; мех. working stressРусско-английский физический словарь > действующее напряжение
-
10 эффективное напряжение
мех. effective stress; эл. rms voltageРусско-английский физический словарь > эффективное напряжение
-
11 среднеквадратичное рабочее напряжение
1.2.9.7 среднеквадратичное рабочее напряжение (rms working voltage): Среднеквадратичное значение рабочего напряжения, включая любые составляющие постоянного напряжения.
Примечание - Среднеквадратичные рабочие напряжения определяют по 2.10.2.2 и, где уместно, - по 1.4.8.
Источник: ГОСТ Р МЭК 60950-1-2009: Оборудование информационных технологий. Требования безопасности. Часть 1. Общие требования оригинал документа
Русско-английский словарь нормативно-технической терминологии > среднеквадратичное рабочее напряжение
-
12 коэффициент искажения синусоидальности кривой напряжения (тока)
- total harmonic distortions
- THD
- distortion factor (of a non-sinusoidal alternating voltage or current)
коэффициент искажения синусоидальности кривой напряжения (тока)
Величина, равная отношению действующего значения суммы гармонических составляющих к действующему значению основной составляющей переменного напряжения (тока).
Примечание. Для целей стандартизации допускается относить к номинальному напряжению (току).
[ ГОСТ 23875-88]
коэффициент нелинейных искажений
коэффициент несинусоидальности
КНИ
Определяет веса высших гармоник переменного напряжения по отношению к основной гармонике. Чем КНИ меньше, тем ближе форма напряжения к чистой синусоиде. Например: синусоидальная форма сигнала (КНИ=0), форма сигнала отлична от синусоидальной, но искажения не заметны на глаз (КНИ<3%), отклонение формы сигнала от синусоидальной заметно на глаз (КНИ>5%), сигнал имеет трапецеидальную или ступенчатую форму (КНИ<21%), сигнал имеет прямоугольную форму (КНИ=43%)
[ http://www.radistr.ru/misc/document423.phtml]
(полный) коэффициент гармоник
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва]EN
total harmonic distortions
THD
RMS value of all harmonics in a waveform (excluding fundamental) divided by RMS value of fundamental. THDV refers to Voltage waveform. THDI refers to Current waveform.
[ http://www.upsonnet.com/UPS-Glossary/]total 3rd order harmonic distortion
коэффициент искажения синусоидальности, вызванный гармоническими составляющими третьего порядка
total harmonic distortion; THD
коэффициент искажения синусоидальности
общий коэффициент несинусоидальностиtotal harmonic current distortion; THDI
коэффициент искажения синусоидальности кривой тока
обшее гармоническое искажение токаtotal harmonic voltage distortion; THDV, THDU
коэффициент искажения синусоидальности кривой напряжения
обшее гармоническое искажение напряженияПараллельные тексты EN-RU
THD is the ratio of harmonic content to the fundamental and provides a general indication of the quality of a waveform.
[Schneider Electric]Коэффициент искажения синусоидальности (THD) представляет собой отношение суммы гармонических составляющих к значению основной составляющей и является основным индикатором качества формы электрического сигнала.
[Перевод Интент]
Тематики
Синонимы
- КНИ
- коэффициент гармоник
- коэффициент искажения
- коэффициент нелинейных искажений
- коэффициент несинусоидальности
- полный коэффициент гармоник
EN
- distortion factor (of a non-sinusoidal alternating voltage or current)
- THD
- total harmonic distortions
DE
FR
- facteur de distortion (d’une tension ou d’un courant alternatif non sinusoïdal)
Смотри также
55. Коэффициент искажения синусоидальности кривой напряжения (тока)
Коэффициент искажения
D. Klirrfaktor
E. Distortion factor (of a non-sinusoidal alternating voltage or current)
F. Facteur de distortion (d’une tension ou d’un courant alternative non sinusoïdal)
Величина, равная отношению действующего значения суммы гармонических составляющих к действующему значению основной составляющей переменного напряжения (тока).
Примечание. Для целей стандартизации допускается относить к номинальному напряжению (току)
Источник: ГОСТ 23875-88: Качество электрической энергии. Термины и определения оригинал документа
Русско-английский словарь нормативно-технической терминологии > коэффициент искажения синусоидальности кривой напряжения (тока)
13 интервал усреднения
- mean
- demand interval “window”
- demand interval
- averaging time period
интервал усреднения
Время, за которое вычисляется среднее значение какой-либо величины.
[Интент]Параллельные тексты EN-RU
Supply Voltage Variations
EN50160 states that, under normal operating conditions, excluding situations arising from faults or voltage interruptions:
• during each period of one week 95% of the ten minute mean rms values of the supply voltage shall be within the range of Un ±10%.
• all ten minute mean rms values of the supply voltage shall be within the range of Un +10% to -15%.
[Schneider Electric]Изменения напряжения питающей сети
В соответствии со стандартом EN50160 в нормальных условиях работы, за исключением ситуаций короткого замыкания или прерывания напряжения:
• на протяжении недели, в течение 95 % времени средние действующие значение напряжения питающей сети, подсчитанные за интервалы усреднения продолжительностью 10 минут, должны находиться в пределах Un ±10 %
• средние действующие значения напряжения питающей сети, подсчитанные за все 10-минутные интервалы усреднения, должны находиться в пределах от +10 до -15 % от Un.
[Перевод Интент]
Тематики
EN
- averaging time period
- demand interval
- demand interval “window”
- mean
Русско-английский словарь нормативно-технической терминологии > интервал усреднения
14 длительный допустимый ток
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-английский словарь нормативно-технической терминологии > длительный допустимый ток
См. также в других словарях:
Voltage regulator — A popular three pin 12 V DC voltage regulator IC. A voltage regulator is an electrical regulator designed to automatically maintain a constant voltage level. A voltage regulator may be a simple feed forward design or may include negative feedback … Wikipedia
RMS — F/A/V Effective sound pressure. (Acoustics) A&V Root mean square. A measure of effective (as opposed to peak) voltage of an AC waveform. For a sine wave, it is .707 times the peak voltage. For any periodic waveform, it is the square root of the… … Audio and video glossary
V RMS — Voltage root mean square; average voltage equal to the maximum voltage multiplied by a constant … Dictionary of automotive terms
Orders of magnitude (voltage) — To help compare different orders of magnitude, the following list describes various voltage levels. Factor (volt) Value Item 10−7 0.5 μV Change in nerve cell potential caused by opening a single acetylcholine receptor channel[1] 10−6 2 μV Noise… … Wikipedia
True RMS converter — When measuring the value of an alternating current signal it is often necessary to convert the signal into a direct current signal of equivalent value (known as the RMS, root mean square, value). This process can be quite complex (see root mean… … Wikipedia
High-voltage direct current — HVDC or high voltage, direct current electric power transmission systems contrast with the more common alternating current systems as a means for the bulk transmission of electrical power. The modern form of HVDC transmission uses technology… … Wikipedia
Extra-low voltage — IEC voltage range AC DC defining risk High voltage (supply system) > 1000 Vrms > 1500 V electrical arcing Low voltage (supply system) 25–1000 Vrms 60–1500 V electrical shock Extra low voltage (supply system) < 25 V … Wikipedia
Root mean square — In mathematics, the root mean square (abbreviated RMS or rms), also known as the quadratic mean, is a statistical measure of the magnitude of a varying quantity. It is especially useful when variates are positive and negative, e.g., sinusoids.It… … Wikipedia
AC power — This article deals with power in AC systems. See Mains electricity for information on utility supplied AC power. Usually hidden from the unaided eye, the blinking of (non incandescent) lighting powered by AC mains is revealed in this motion… … Wikipedia
Audio power — Sound measurements Sound pressure p, SPL Particle velocity v, SVL Particle displacement ξ Sound intensity I, SIL Sound power Pac Sound power level SWL Sound energy Sound energy density … Wikipedia
Alternating current — (green curve). The horizontal axis measures time; the vertical, current or voltage. In alternating current (AC, also ac) the movement of electric charge periodically reverses direction. In direct current (DC, also dc), the flow of electric charge … Wikipedia
Перевод: с русского на английский
с английского на русский- С английского на:
- Русский
- С русского на:
- Все языки
- Английский
- Немецкий
- Французский